Can someone please school me on the Mod 7?

What are the specs, is it an actual SYKW offering?

it was a ganza release of about 50, a dumpster mutt with some serrations.

Thanks for the information, I saw one on Ebay and was curious <img src="/ubbthreads/images/graemlins/wink.gif" alt="" />

To amplify, a DMDC with serrations if I remember correctly.

It was a very limited offering.
1/4" thick. overall 9-1/2"
double cut finish
Resiprene-C handle

Here's the BladeForums post:
YOWZA!!!!. . . . Scrap Yard Mil. Overrun At The Razorganzaaaaa!!!

After much yelping from the pack (including myself), the terms of the contest were reversed so that we got the first minute instead of the Hogs. During the Razorganzaaa, they were labeled the Military Overrun Dog and were #7 in the list of knives offered, so they were referred to as MOD7s.

Also, they were released at $119.95; I've paid up to $170 on the secondary market for them, and have seen them sell for more, but that's as high as I've been willing to go.

Here's a Mod7 beside the Bolo
<img src="/ubbthreads/images/graemlins/ooo.gif" alt="" /> Did someone say Bolo---
Bolo,Bolo,Bolo,Bolo,Bolo,Bolo,Bolo,Bolo,Bolo,Bolo,Bolo,Bolo,
Bolo,Bolo,Bolo,Bolo,Bolo,Bolo,Bolo,Bolo,Bolo,Bolo,Bolo,Bolo,
Bolo,Bolo,Bolo,Bolo,Bolo,Bolo,Bolo,Bolo,Bolo,Bolo,Bolo,Bolo

I have a MOD 7, and I was wondering if it was a legit one or not.

Is there any way to tell just by looking at the knife to be sure it isn't a good looking copy?

Welcome to the Yard! <img src="/ubbthreads/images/graemlins/laugh.gif" alt="" /> Always nice to see another Hoosier here. I’ve never heard of a counterfeit SY knife, so you should be good. How to tell w/o looking, go whup on it and see if it breaks or not. <img src="/ubbthreads/images/graemlins/laugh.gif" alt="" />

well you could try your best to destroy it

if you fail then its authentic <img src="/ubbthreads/images/graemlins/cool.gif" alt="" />

I think Andy and Stihl have said it right; go put it through some rough love, and if it stands up, then it's most likely legit!

A Mod 7 in CM154/kydex would make a great SCUBA knife....Dan??? Anyone given SR77 much "wet" use? If you looked after it, it might work....?

I just did an "I'll take it" on another MOD 7. It appears that they reallocated the first position sheath to a DMLE, replacing it with a custom kydex + Teklok. It's been sharpened, so I guess I'll consider it my user.

What makes you doubt it's authentic? Take a look at the release posting (link above) and the other picture in this thread. That SY logo is stamped into the blade, and MODs have old-style Busse Combat Basic handles -- Is there a counterfeit Scrap Yard ring out there I haven't heard about?

I saw that one too, Jim. I was tempted, but passed, Congrats on the new to you MOD7. <img src="/ubbthreads/images/graemlins/cool.gif" alt="" /> <img src="/ubbthreads/images/graemlins/thumbup.gif" alt="" />

Thanks; I keep telling myself that I'm saving up for Knob Creek, but I don't appear to be listening.

I can relate to that completely! <img src="/ubbthreads/images/graemlins/wink.gif" alt="" />

I really hope I can make it up there again... <img src="/ubbthreads/images/graemlins/crossfingers.gif" alt="" /> <img src="/ubbthreads/images/graemlins/crossfingers.gif" alt="" />

I guess I was wondering if there WERE any counterfeits roaming around out there. It looks like it should, but it was not very sharp when I rec'd it in the mail from the guy. Are scrapyards usually only kinda sharp when they are new? Also, there was some very minimal rust spotting on the blade. How rust prone is SR77?

Scrapyards can vary from very sharp to not so sharp from the factory. The DC finish is more prone to rusting than the other finishes due to micro pitting from the process.

Thanks Ted.

What steps should one take to minimize this from happening again after the rust is removed?

SR77 and SR101 are both high carbon steels that do rust; INFI is also classified as a carbon steel, but has proven to be stain resistant. I recall a thread where uncoated corrosion comparisons were done and SR77 was identified as developing surface rust fairly easily, but that the rust did not pit the blade nearly as much as SR101.

Most recommendations were to use a coating of non-animal fat based oil (like olive oil) so that it won't go rancid or be poisonous if you intent to prep food with your knife. A lot of folks swear by a wiping down the blade with a Marine Tuff Cloth. Others have also said that if you just wipe the blade with a dry cloth after use, that's been good enough for them.

WD40 periodically works too.

I have a Kydex sheath for the MOD 7 and I think it sucks.

The thing is soooo tight that It messes up the handle every time I have to yank it out. It is so difficult to remove that it is almost unsafe.

I want a new sheath.

Is the Scrapper 6 sheath on the store good for the MOD 7? Anyone have suggestions as to where I could get a nice sheath (either leather or nylon) for the MOD 7?

thanks!

leather


pm "rainwalker" here on the forum

0311Hoosier, are you referring to the first position ones from the store. If so, I agree with you totally. The kydex from the store is unusable IMO. The retention is too tight, and it cannot be adjusted. I recommend Rainwalker or Okuden for kydex

it can easily be adjusted actually... with a hairdryer.
<img src="/ubbthreads/images/graemlins/laugh.gif" alt="" />

you can ask for some details from some more experienced kydex users.

My sheath was also almost unusable and I adjusted my kydex with a hairdryer. It took a couple of tries to get it just where I wanted, but I was shocked how easy it was to modify. Don't throw it out without trying to mod it....

Yep, hairdryers work wonders with kydex sheaths that are to tight.