Scrap Yard Discussion Forums

Previous Thread
Next Thread
Print Thread
Page 3 of 3 1 2 3
Re: SR-101 Chips [Re: Cliff Stamp] #1031507 09/08/15 11:46 AM
Joined: Apr 2014
Posts: 1,130
A
Anton Beukes Offline OP
Junk Yard Dog
OP Offline
Junk Yard Dog
A
Joined: Apr 2014
Posts: 1,130
Originally Posted by Cliff Stamp
Originally Posted by Anton Beukes
And again today chopping some camelthorn wood my 1111 chipped, both my regulator and 911 had the same results. All three knives have a 17dps edge angle with a 25dps micro bevel.


Anton, as a quick question, would it be possible to you to run a side by side comparison of another knife which doesn't chip on the same type of wood while you are using the one that does chip and see if :

-the SR101 knife chips again
-the other one doesn't

If this happens, continue using the other knife that didn't chip for say the same length of time again to see if it chips as well.



Wow..... Cliff Stamp. Welcome

Re: SR-101 Chips [Re: Private Klink] #1031508 09/08/15 11:48 AM
Joined: Apr 2014
Posts: 1,130
A
Anton Beukes Offline OP
Junk Yard Dog
OP Offline
Junk Yard Dog
A
Joined: Apr 2014
Posts: 1,130
Originally Posted by Private Klink
Cliff, Howdy and Welcome to the Scrap Yard! smile


I will try get some 5160.

Re: SR-101 Chips [Re: Anton Beukes] #1031530 09/09/15 12:02 AM
Joined: Mar 2007
Posts: 10,802
coyotebc Offline
Junk Yard Dog
Offline
Junk Yard Dog
Joined: Mar 2007
Posts: 10,802
Cliff
If memory serves me
You are Canadian correct?
If so maybe we can set up a test of my 1311 with you


The stripes of a tiger don't wash away. Be a man of steel not clay JYD #102
Re: SR-101 Chips [Re: coyotebc] #1031531 09/09/15 12:56 AM
Joined: Apr 2014
Posts: 1,130
A
Anton Beukes Offline OP
Junk Yard Dog
OP Offline
Junk Yard Dog
A
Joined: Apr 2014
Posts: 1,130
Originally Posted by coyotebc
Cliff
If memory serves me
You are Canadian correct?
If so maybe we can set up a test of my 1311 with you


Good idea....

Re: SR-101 Chips [Re: Anton Beukes] #1031890 09/20/15 03:28 PM
Joined: Jun 2012
Posts: 2,669
Y
yesh Offline
Junk Yard Dog
Offline
Junk Yard Dog
Y
Joined: Jun 2012
Posts: 2,669
Anton, so just to clarify the edges stabilized for you after sharpening away some of the metal at the apex?


Junk Yard Dog #152 - Woof!
Re: SR-101 Chips [Re: yesh] #1031957 09/22/15 12:42 PM
Joined: Apr 2014
Posts: 1,130
A
Anton Beukes Offline OP
Junk Yard Dog
OP Offline
Junk Yard Dog
A
Joined: Apr 2014
Posts: 1,130
Originally Posted by A Fond Farewell
Anton, so just to clarify the edges stabilized for you after sharpening away some of the metal at the apex?


Yes, it seems like it. One have to also make sure to form the apex properly and get rid of the burr.

Page 3 of 3 1 2 3

Powered by UBB.threads™ PHP Forum Software 7.7.3